笔记本电脑壳上壳冲压模具设计(含CAD零图,CAXA图)

笔记本电脑壳上壳冲压模具设计(含CAD零图,CAXA图)(任务书,开题报告,论文说明书11200字,CAD图6张,CAXA图6张)
摘  要
随着社会的飞速发展和科学技术的不断进步，人们对电脑的依赖也是日益加剧，正是这需求推动了科技的发展，使得电脑外形的不断改革，并衍生出了笔记本电脑这一便携、小巧的个人电脑。随着笔记本电脑的不断普及，笔记本电脑的保护与维修方面的问题也迎面而来。由于笔记本电脑重量较轻，因此不能像台式电脑那样有厚重的机壳来保护，于是笔记本电脑壳上壳便应运而生。笔记本电脑壳上壳主要是附着在笔记本电脑外壳上，用来保护笔记本电脑，防止它因与外界的碰撞而损坏的。但是，如今市面上许多的笔记本电脑壳上壳并不能有效的起到保护的作用。因此，优化笔记本电脑壳上壳很有必要。
本文通过对笔记本电脑壳上壳的外形进行分析，从而计算得出用来冲压壳上壳的模具的相应尺寸。通过其外形的形状，提出了三种冲压模具的设计方案，先进行落料工序，做出初步的轮廓，再经过弯曲工序使其外形进行弯曲，从而能够扣在笔记本外壳上，最后进行冲孔，使它能够露出笔记本的logo和电源指示灯。最后我对各个冲压模具的零件进行了设计和图纸绘制，并且校核了它的强度，所得结果对于笔记本电脑壳上壳冲压模具的设计有较大的帮助。

[资料来源：http://Doc163.com]

本论文主要研究了笔记本电脑壳上壳的形状尺寸和对应的冲压模具所需的尺寸，以及各个冲压模具的工作原理，对冲压模具进行了设计，并校核了其零件的强度，绘制了零件图和总装图。
关键词：笔记本电脑壳上壳；冲压模具；设计；校核

Abstract
With the continuous progress of the society and the rapid development of science and technology, people rely on computers is growing is demand that promoted the development of science and technology, the continuous reform in the shape of a computer, the portable notebook computer, compact size of personal computers are derived. With the popularity of notebook computers, the problems in the protection and maintenance of notebook computers are coming. Due to the lighter notebook computers, and therefore can not be like a desktop computer with a thick shell to protect, so the laptop shell on the shell. Laptop shell is mainly attached to the notebook computer shell, used to protect the notebook computer, to prevent it due to the collision with the outside world. However, many of the laptop shell on the market now can not effectively play a protective role in the market. Therefore, it is necessary to optimize the laptop shell.

[资料来源：https://www.doc163.com]

In this paper, by analyzing the shape of the shell of the notebook computer, the corresponding size of the die used for pressing the shell is calculated. Shape by the shape of the proposed three kinds of stamping die design, advanced line blanking process, make a preliminary outline, after bending process enable its shape bend, so as to be able to button on the outer shell of the notebook, the punching, enable it to reveal notebook logo, and a power supply indicating lamp. At last, I design and draw the parts of the stamping dies, and check the strength of the parts, and the results have great help to the design of the stamping die for the shell of the notebook computer.
This paper mainly studies the stamping mould for the shell of the notebook computer shell size and shape corresponding to the desired size, and various stamping die working principle and on the metal stamping die design and check the intensity of the parts, and draw the part drawing and assembly drawing.
Key Words：Laptop shell‘s  shell; Stamping die; design; check [资料来源：http://Doc163.com]

  [来源：http://www.doc163.com]

[资料来源：http://Doc163.com]
目  录
第1章 绪论    1
  1.1 引言    1
  1.2 冲压模具概述    1
    1.2.1 冲压模具的分类    1
    1.2.2 冲压模具发展现状    3
  1.3 笔记本电脑壳上壳设计的主要内容    4
第2章 冲压工艺规程的编制    4
  2.1 冲压件的工艺分析    4
  2.2 排样设计及材料利用率计算    5
    2.2.1 排样设计    5
    2.2.2 材料利用率计算    5
  2.3 工艺方案的确定    6
第3章 落料模、弯曲模、冲孔模的设计    7
  3.1 冲压模具模架选择    7
  3.2 导套、导柱的设计    9
  3.3 冲裁间隙的选择    10
    3.3.1 冲裁间隙概述    10
    3.3.2 合理的冲裁间隙的计算    10 [资料来源：Doc163.com]
  3.4 凸、凹模尺寸确定    12
  3.5 压力中心的确定和冲压力的计算与校核    12
  3.6 冲模典型零件设计    13
    3.6.1 落料模和冲孔模的凸模设计    14
    3.6.2 落料模和冲孔模的凹模设计    15
    3.6.3 弯曲模的凸模设计    16
    3.6.4 弯曲模的凹模设计    16
    3.6.5 定位装置的设计和卸料装置的设计    17
第4章 结论与展望    18
  4.1 研究结论    18
  4.2 展望    18
参考文献    20
致谢    21 [资料来源：http://Doc163.com]