Open Nav

支承套零件加工工艺编程及夹具的设计

以下是资料介绍,如需要完整的请充值下载.
1.无需注册登录,支付后按照提示操作即可获取该资料.
2.资料以网页介绍的为准,下载后不会有水印.仅供学习参考之用.
   帮助中心
资料介绍:

支承套零件加工工艺编程及夹具的设计(含任务书,开题报告,设计说明书19000字,CAD图纸2张)
摘    要
高效率、高精度加工是数控机床加工最主要特点之一。利用数控机床加工,其产品加工的质量一致性好,加工精度和效率均比普通机床高出很多,尤其在轮廓不规则、复杂的曲线或曲面、多工艺复合化加工和高精度要求的产品加工时,其优点是传统机床所无法比拟的。本课题对异性体、复杂的曲线、多工艺复合化加工进行探索,设计出三种切实可行的工艺流程及工艺装备。在产品的加工过程中,工件在夹具内的定位和夹紧显得特别重要。须根据六点定位对产品进行合理的定位,欠定位、完全定位还是过定位都须根据实际的生产过程决定。夹具是涵盖了从加工到组装的几乎所有操作过程的一种装夹设备。由于大量的加工操作需要装夹,夹具设计在制造系统中就变得非常重要,它直接影响加工质量,生产率和制造成本。本文通过分析支承套的结构特点和加工要求,制定了一套较合理的夹具设计,从而为保证该零件的加工精度将提供一种经济实用的工艺装备,具有一定的实用价值。通过对各种定位夹紧装置的分析比较,选择并组合了一套既能够满足加工要求的,又比较简洁的装置,并对各工步进行数控编程。

[来源:http://www.doc163.com]

关键词:数控加工,工艺流程,工艺装备,夹具设计


Components Numerical Control Processing Craft Analysis
and Craft Equipment Design

ABSTRACT

The high efficiency, the precision work are one of numerical control engine bed processing most main characteristics. Using the numerical control engine bed processing, its product processing quality uniformity is good, the processing precision and the efficiency outdo compared to the ordinary engine bed very much, especially when outline not rule, complex curve or curved surface, multi-craft recombine processing and high accuracy request product processing, its merit is the traditional engine bed is unable to compare. This topic to the opposite sex body, the complex curve, the multi-craft recombine processing carries on the exploration, designs three practical and feasible technical processes and the craft equipment. In the product processing process, the work piece appears in jig localization and the clamp specially importantly. Must act according to six localizations to carry on the reasonable localization to the product, owes the localization, locates completely crosses the localization all to have to act according to the actual production process decision. The jig covered from has processed clamps the equipment to the assembly nearly all operating process one kind of attire. Because the massive processing operation needs to install clamps, the jig design changes can it be that the constant weight in the manufacture system to want, it affects the processing quality directly, the productivity and the production cost. This article through the analysis support components, the air compressor snifting valve lid as well as the supporting the unique feature and the processing request which wraps, has formulated a set of reasonable jig design, thus for guaranteed this components the processing precision will provide one economical practical craft equipment, will have certain practical value. Through to each kind of localization clamp analysis comparison, chose and combines a set both to be able to satisfy the processing request, and the quite succinct installment, and carried on the numerical control programming to each step working procedure.

[资料来源:http://doc163.com]



Key word:  numerical control processing, technical process, craft equipment, jig design
  [资料来源:http://Doc163.com]

支承套零件加工工艺编程及夹具的设计
支承套零件加工工艺编程及夹具的设计
支承套零件加工工艺编程及夹具的设计
支承套零件加工工艺编程及夹具的设计


目  录

摘要…………………………………………………………………………  1

[资料来源:http://Doc163.com]

ABSTRACT……………………………………………………………………  2
0 引言………………………………………………………………………  4
1 数控加工技术概述………………………………………………………  5
1.1 数控加工技术的发展…………………………………………………  5
1.2 数控加工工艺的特点…………………………………………………  6
[资料来源:http://doc163.com]

1.3 数控机床与普通机床相比具有的优越性……………………………  7
2 夹具设计过程……………………………………………………………  9
2.1 设计夹具的目的………………………………………………………  9
2.2 夹具的分类…………………………………………………………  10
2.3 专用夹具的组成……………………………………………………  12
2.4 典型的定位元件……………………………………………………  13

[资料来源:http://www.doc163.com]


2.5 夹具中的夹紧机构…………………………………………………  16
2.6 夹具的发展趋势……………………………………………………  17
3 机械加工工艺规程的制定……………………………………………  19
3.1 机械加工工艺规程的作用…………………………………………  20
3.2 机械加工工艺规程的制定程序……………………………………  20   
3.3 毛坯的选择…………………………………………………………  21

[资料来源:http://Doc163.com]


3.4 定位基准的选择……………………………………………………  22
3.5 零件表面加工方法的选择…………………………………………  24
3.6 加工顺序的安排……………………………………………………  25
4.1 支承套………………………………………………………………  27
4.1.1 零件加工工艺分析………………………………………………  27
4.1.2 毛坯的选择………………………………………………………  28 [来源:http://www.doc163.com]
4.1.3 数控加工工艺分析及工序设计…………………………………  31
4.1.4夹具设计…………………………………………………………  34
5 结论……………………………………………………………………  36
6 致谢……………………………………………………………………  37
参考文献…………………………………………………………………  38 [资料来源:www.doc163.com]
附录1……………………………………………………………………  39
[资料来源:Doc163.com]

  • 关于资料
    提供的资料属本站所有,真实可靠,确保下载的内容与网页资料介绍一致.
  • 如何下载
    提供下载链接或发送至您的邮箱,资料可重复发送,若未收到请联系客服.
  • 疑难帮助
    下载后提供一定的帮助,收到资料后若有疑难问题,可联系客服提供帮助.
  • 关于服务
    确保下载的资料和介绍一致,如核实与资料介绍不符,可申请售后.
  • 资料仅供参考和学习交流之用,请勿做其他非法用途,转载必究,如有侵犯您的权利或有损您的利益,请联系本站,经查实我们会立即进行修正! 版权所有,严禁转载
    doc163.com Copyright © 2012-2024 苏ICP备2021029856号-4