Open Nav

研究楔横轧成形的影响以及钛髋关节假体的锻造和模锻的形成

以下是资料介绍,如需要完整的请充值下载.
1.无需注册登录,支付后按照提示操作即可获取该资料.
2.资料以网页介绍的为准,下载后不会有水印.仅供学习参考之用.
   帮助中心
资料介绍:

研究楔横轧成形的影响以及钛髋关节假体的锻造和模锻的形成(中文7000字,英文5500字)
为了降低锻造零件的生产成本,有可能采用不同的方法。尤其是像钛这样价格较高的材料,其材料成本占生产成本很大的一部分。因此,减少初始材料的用量可以显著降低总成本。为了改善这种状况,人们研究了现有的锻造工艺。对于钛型髋关节置换术,开发了一种锻造工艺。为了减少最初材料的需要,研究了楔横轧作为一种预成型的材料,并对其进行了模锻。不同的锻造阶段对最终结果的影响进行了详细分析和介绍。为了提高新开发的闪速锻造工艺的预测精度,减少模具设计的迭代循环,研究了锻造环境边界条件下的可行仿真参数,这是用有限元分析进行的,并且考虑到对形式填充、过程的稳定性、模具压力的影响。采用楔横轧、模锻和闪速制动以及新开发的锻造工艺可将闪速率从69%大幅降低到32%。
楔横轧、锻造、锻造序列发展、有限元模拟。
Investigating the effects of cross wedge rolling preforming operation and die forging with flash brakes on forging titanium hip implants
Bernd-Arno Behrens 1 & Malte Stonis2 & Thoms Blohm2 & Johannes Richter2

Received: 27 September 2016 / Accepted: 4 November 2016 [资料来源:http://www.doc163.com]
# Springer-Verlag France 2016

Abstract To reduce production costs of forged parts, different approaches are possible. Especially for valu- able materials like titanium, material costs represent a large part of the production costs. Therefore, reducing the initial material can decrease the total costs signifi- cantly. In order to identify the potential for improve- ments, an existing forging sequence was in vestigated. For a titanium hip implant, a forging sequence was de- veloped. To reduce the initially needed material, cross wedge rolling as a preforming operation and die forging with flash brakes was investigated. The influence of the different stages on the final result was analysed and presented in detail. To  increase  the  prediction  accuracy of the newly developed flash-reduced forging  sequence and decrease iteration loops of die designs, feasible sim- ulation parameters considering the boundary  conditions of the forging environment were investigated. This is done using Finite Element Analysis (FEA), considering form filling, process stability, die stress and press forces. Using cross wedge rolling and die forging with flash brakes, the newly developed forging sequence re- duces the flash rate significantly from 69% to 32%. [资料来源:http://Doc163.com]
Thoms Blohm blohm@iph-hannover.de

[资料来源:Doc163.com]

  • 关于资料
    提供的资料属本站所有,真实可靠,确保下载的内容与网页资料介绍一致.
  • 如何下载
    提供下载链接或发送至您的邮箱,资料可重复发送,若未收到请联系客服.
  • 疑难帮助
    下载后提供一定的帮助,收到资料后若有疑难问题,可联系客服提供帮助.
  • 关于服务
    确保下载的资料和介绍一致,如核实与资料介绍不符,可申请售后.
  • 资料仅供参考和学习交流之用,请勿做其他非法用途,转载必究,如有侵犯您的权利或有损您的利益,请联系本站,经查实我们会立即进行修正! 版权所有,严禁转载
    doc163.com Copyright © 2012-2024 苏ICP备2021029856号-4